online album mastering

온라인 앨범 마스터링 — 응집력 및 출시 준비 파일

~에 의해 Byron Hill II ~에 뉴스

앨범 마스터링은 단순히 노래를 더 크게 만드는 것이 아닙니다. 시퀀싱, 톤 일관성, 깔끔한 간격, 그리고 모든 플랫폼 검사를 통과하는 전달입니다. 파일만 완성하는 것이 아니라 레코드를 완성하는 온라인 앨범 마스터링 서비스를 이용하세요.

앨범 마스터링 시작 →

I. 온라인 앨범 마스터링으로 얻는 것

  • 트랙 간 일관된 사운드: 앨범이 하나의 이야기처럼 재생되도록 톤과 인지된 음량을 맞춤.
  • 시퀀싱 & 간격: 필요에 따라 세련된 간격, 크로스페이드, 라이브 무간격 흐름.
  • 모든 매체에 대한 전달: CD 복제를 위한 DDP 이미지, 스트리밍 마스터(WAV), 그리고 동일한 시작점에 맞춘 라벨이 붙은 대체본(클린/라디오, 인스트루멘털, 아카펠라).
  • QC & 피드백: 번역 점검(이어버드, 자동차, 작은 스피커), 진정한 피크 안전성, 그리고 믹스 조정이 결과를 개선할 수 있다면 간단하고 실행 가능한 메모.
앨범 전달 필수 사항
  • 세션 샘플 레이트에 맞춘 트랙별 24비트 WAV (믹스버스 리미터/클리핑 없음).
  • 좋아하는 참조 두 개(그리고 싫어하는 하나)와 간단한 메모.
  • 최종 트랙 순서, 간격/크로스페이드 메모, ISRC(할당된 경우), 앨범 UPC.

II. 앨범에 마스터링이 필요한 이유 (단순한 “e-마스터링”이 아니라)

단일 트랙 자동화는 음량 수치를 맞출 수 있지만, 앨범에는 맥락이 필요합니다: 트랙 1 다음에 트랙 2가 어떻게 이어지는지, 조용한 간주가 어떻게 귀를 재설정하는지, 라이브 세그웨이가 클릭 없이 어떻게 끊김 없이 이어지는지. 온라인 앨범 마스터링은 이러한 관계를 처리하고 한 번에 올바른 포맷을 제공합니다.

III. 과정 (명확하고 온라인)

  1. 업로드 및 노트: 믹스, 참조, 트랙 순서, 간격/크로스페이드 지침 전송.
  2. 첫 번째 작업: 일관된 톤, 맞춘 음량, 간격, 예비 전달물.
  3. 검토: 사용자의 시스템에서 청취; 간결한 타임스탬프 노트 공유(앨범 전체용 한 장).
  4. 수정: 집중 업데이트, 시퀀싱 확인, 최종 품질 검사.
  5. 최종 전달: DDP 이미지(CD-텍스트/ISRC/UPC 포함), 스트리밍 마스터(WAV), 요청한 모든 대체본—모두 라벨링 및 정렬 완료.

IV. 전달물 (앨범 준비 완료)

전달물 포맷 메모
스트리밍 마스터 세션 속도의 WAV 24비트 트루 피크 안전 한계; 일관된 인지 음량
기악 / 아카펠라 WAV 24비트 메인에 정렬됨; 트랙 번호별 라벨링
클린 / 라디오 편집본 WAV 24비트 시퀀싱 유지; 메인과 타이밍 일치

V. 음량 및 변환 (앨범 접근법)

앨범은 고정된 LUFS 수치 하나로 결정되지 않습니다. 트랙 간 인지된 음량을 균형 있게 조절하고, 안전한 트루 피크로 트랜지언트를 보호하며, 친밀한 인트로부터 웅장한 클로저까지 내러티브를 유지하여 이어폰, 자동차, 클럽 시스템 어디서나 앨범이 잘 어우러지도록 합니다.

VI. 가격 및 일정

  • 앨범 범위 내 트랙당 요금: 8개 이상의 트랙에 대한 가격 조정; 스템 또는 복잡한 편집은 필요에 따라 견적 제공.
  • 처리 시간: 첫 번째 작업은 일반적으로 5~7 영업일 소요, 이후 빠른 수정 가능. 긴급 요청 가능.
  • 수정: 집중된 수정 세트 1회 포함; 추가 수정도 필요 시 간단히 진행 가능.

앨범 견적 받기 →

VII. 이 서비스가 다른 점

  • 앨범 우선 사고방식: 결정은 트랙별 고립이 아닌 순서에 따라 이루어집니다.
  • 정렬된 대체 버전: 인스트루멘털, 아카펠라, 클린/라디오 버전이 샘플 단위로 정확히 맞춰집니다.
  • 실용적 소통: 명확하고 시간 표시된 노트와 빠른 반복으로 진행 속도 유지.
  • 전문 모니터링 & 경험: 3,000곡 이상 마스터/믹스, 여러 시스템에서 상세한 번역 검수 완료.

VIII. 자주 묻는 질문

CD를 프레스하지 않으면 DDP가 필요 없나요?
스트리밍에는 필수는 아니지만, 많은 아티스트가 나중에 프레스 준비를 위해 DDP를 보관합니다.

갭 없는 라이브 앨범도 처리할 수 있나요?
네—연속 렌더링 또는 정확한 크로스페이드 노트를 제공하면 매끄러운 전환을 유지합니다.

ISRC/UPC는 어떻게 하나요?
트랙별 ISRC와 앨범용 UPC가 있으면 제공해 주세요. 없으면 진행하며 배포 시 코드를 추가할 수 있습니다.

앨범 음량은 얼마나 될까요?
경쟁력 있는, 음악적인 음량과 진정한 피크 안전성을 목표로 합니다. 단일 LUFS 값을 쫓기보다 트랙 간 인지가 더 중요합니다.

싱글도 마스터링하나요?
네—싱글, EP, 디럭스 에디션 모두 가능합니다. 싱글이 앨범에 앞서 나올 경우, 통합 시 그 톤을 존중합니다.

IX. 온라인으로 앨범 마스터링할 준비가 되셨나요?

믹스를 업로드하고, 순서를 공유하세요. 저희가 응집력, 간격, 전달을 처리합니다. 앨범은 스튜디오에서 출시 준비 완료 상태로 나갑니다—요청 시 DDP, 스트리밍 마스터, 정렬된 대체 버전 포함.

온라인 앨범 마스터링

이전 게시물 다음 게시물

관련 게시물

How to Use Vocal Presets in Studio One

How to Use Vocal Presets in Studio One

In Studio One, a “vocal preset” is a reusable channel chain—EQ, compression, de-essing, tone color, delay, and reverb—that you can load in one move. This guide shows how to choose and load presets (FX Chains and Track Presets), set healthy gain, adapt tone to your mic, route sends, automate scenes, and save role-based versions for lead, doubles, harmonies, and ad-libs. If you want a tuned springboard, browse purpose-built Studio One vocal presets and then fine-tune thresholds and sends for your voice and room. I. What a “vocal preset” is in Studio One Studio One gives you several preset containers that make vocal chains easy to load and reuse: FX Chain preset — a saved insert stack with Macro controls (one-click channel strip). Track Preset — recalls inserts, order, I/O, color, and sends for a track (Studio One 6+). Song Template — opens a whole session “studio-ready” (lanes + FX channels prewired). Device presets — per-plug-in settings (Pro EQ³/Pro EQ², Compressor, De-Esser, Analog Delay, Room Reverb/OpenAIR, etc.). Loading a preset is step one. Step two is adapting input level, de-ess amount, presence, air, and FX balance to your voice and the song. II. Pre-flight (so presets behave) Pre-flight checklist Audio device & buffer: smaller buffer (64–128) while tracking; raise later for mixing. Session rate: 44.1 kHz for music (48 kHz if delivering to video). Input target: sing at performance level; aim raw peaks around −12 to −8 dBFS before any inserts. Track layout: one audio track named Lead Vox and two FX channels (A = Slap, B = Plate). Pop filter & distance: 10–20 cm from mic; stay consistent to stabilize tone. III. Load a vocal preset (four reliable routes) 1) FX Chain preset (fastest, macro-ready) Open the Browser (F5) → Effects → FX Chains → drag your chain onto the Lead Vox channel. Click the Macro panel (wrench icon) to expose Trim, De-Ess, Body, Presence, Air, and FX controls. Save your working copy (right-click channel header → Store FX Chain) as Lead — Clean (YourName). 2) Track Preset (lane + sends in one move) Right-click a track header → Apply Track Preset… (or drag from Browser → Track Presets). Set input, arm, and monitor. Your inserts and sends load together. 3) Song Template (start ready) New Song → pick your “Vocal Starter” template with Lead/Doubles/Harmonies/Ad-libs and Slap/Plate FX channels. Set inputs and record; everything else is prewired. 4) Drag-drop device presets In the Browser, drag device presets (Pro EQ³, Compressor, De-Esser, etc.) into empty insert slots to build a chain, then Store FX Chain. IV. Gain staging: make or break Interface pre first: set the mic pre so unprocessed peaks land −12 to −8 dBFS. Clip Gain / Event Gain: nudge loud/soft phrases (±2–3 dB) before compression; add short fades at edit points. Comp A target: aim ~3–5 dB gain reduction on phrases (ratio 2:1–3:1; attack 10–30 ms; release 80–160 ms). Don’t slam 10–12 dB constantly. Post-chain peak: keep track peaks around −6 to −3 dBFS; leave loudness for mastering. Level-match A/B: keep a final Gain/Trim at chain end so comparing presets isn’t skewed by “louder wins.” V. Five controls you’ll touch on every song De-Ess (6–8 kHz): turn until earbuds stop complaining; stop before consonants blur. Body (120–200 Hz): add warmth if thin; if the booth is boxy, reduce 250–350 Hz instead. Presence (3–4 kHz): tiny, wide lift only if diction hides. If hats/claps are bright, carve the beat rather than boosting the voice. Air (10–12 kHz): micro shelf only after sibilance is calm. FX blend: slapback 90–120 ms + short plate 0.7–1.0 s (pre-delay 20–50 ms). Verses drier; hooks open. VI. Lead vs. stacks: build a “family,” not clones Lead: mono-true center; minimal wideners; ride volume to keep the story forward. Doubles L/R: higher HPF than Lead; a touch more de-ess; tuck −6 to −9 dB under; micro-pan L/R; avoid chorus wideners that collapse in mono. Harmonies: darker EQ; wider than doubles; optional +0.5–1 dB near 5 kHz for shimmer only if needed. Ad-libs: narrow bandwidth (HPF ~200 Hz, LPF ~8–10 kHz); side-panned; short throw echoes on transitions. Save one FX Chain or Track Preset per role—Lead — Clean, Double — Tight, Harmony — Wide, Ad-Lib — Phone—so recall is instant and consistent. VII. Time & space: FX channels do the heavy lifting Create two FX channels: A = Slap (Analog Delay or Beat Delay), B = Plate (Room Reverb/OpenAIR plate IR). Filter returns: insert Pro EQ³ on each FX channel; HPF ~150 Hz, LPF ~6–7 kHz so tails never hiss on earbuds. Ducking trick: insert Compressor on the Slap FX channel; sidechain from Lead; fast attack/release; ~1–2 dB GR so echoes bloom in the gaps. Send automation: +1–2 dB into hooks; lower in dense verses; keep tails filtered. VIII. Macro Controls (FX Chains = your channel strip) Open the FX Chain editor → Macro Controls. Create knobs: Trim, De-Ess, Body, Presence, Air, FX. Map each knob to the key parameter (e.g., De-Esser amount, Pro EQ shelves, Delay/Reverb sends). Set useful ranges so a quarter-turn does something musical, not extreme. Store the FX Chain so every session loads with your “channel strip” in one click. IX. Stock “safe chain” (rebuildable anywhere) Pro EQ³/Pro EQ² (first): HPF 80–100 Hz; wide −1 to −2 dB at 250–350 Hz if boxy; tight notch near 1 kHz if nasal. Compressor (Comp A, shape): ratio 2:1–3:1; attack 10–30 ms; release 80–160 ms; ~3–5 dB GR on phrases. De-Esser: center ~6–8 kHz; reduce until S/T/SH are comfortable on earbuds. Compressor (Comp B, catcher): faster, 1–2 dB GR to stabilize send levels and peaks. Color (optional): Softube-style Saturation Knob (if installed) or stock Saturation; very low mix; output matched. Pro EQ (polish): +0.5–1 dB broad at 3–4 kHz only if diction hides; tiny 10–12 kHz shelf last. Sends: Analog/Beat Delay for slap; Room Reverb/OpenAIR plate; filter returns. Wrap as an FX Chain; add Macro controls; save as Lead — Stock Clean (S1); branch lighter/heavier variants per song. X. Fast audition (without fooling your ears) Loop a 10–20 s phrase with quiet and loud words. Keep a final Gain at chain end to level-match; flip FX Chains or Track Presets from the Browser. Pick what translates on earbuds/phone, not just the brightest option. XI. Two-track beat survival (bright hats, heavy subs) When the instrumental is a stereo file, reduce collisions instead of “more bright” on the voice: Mid dip on the beat (dynamic): insert Pro EQ on the instrumental bus; create a gentle bell around 3 kHz; sidechain a Compressor to the vocal and link (or automate) the EQ band for −1–2 dB only while the voice speaks. Splash control: keep the Lead’s Air conservative; LPF returns ~6–7 kHz if hats are icy. Mono check: temporarily sum the monitor path; the story should still land on a phone speaker. XII. Tracking vs. mixing: what to print Record dry, hear wet: monitor through the preset on Lead but print a clean take. If a collaborator needs the “demo vibe,” bus Lead to a PRINT track and record a wet safety (Lead_Wet). Commit late: render/freeze heavy FX near the end; keep an _FXPRINT audio track for recall. XIII. Automation that sells the line (micro, not macro) Volume rides: +0.5–1 dB into downbeats; −0.5 dB on tongue-twisters. De-ess threshold: slightly tighter on bright syllables; looser on dark phrases. FX choreography: lift Slap/Plate into hooks; lower in verses; keep tails filtered. XIV. Organization & recall (minutes now, hours later) Names that sort: Lead — Clean, Lead — Air+, Rap — Punch, Harmony — Wide, Ad-Lib — Phone. One per role: separate FX Chains/Track Presets for Lead/Doubles/Harmonies prevent over-de-essing stacks or over-brightening the center. Template: keep a “Starter — Vocals (Studio One)” Song Template with lanes and FX channels; start every song from it. XV. Troubleshooting (problem → focused move) Harsh S’s after adding Air: raise De-Esser slightly; reduce Air ~0.5 dB; LPF returns to ~6–7 kHz. Vocal sinks under 808: keep verses drier; add a tiny Presence lift; apply a subtle 2–4 kHz dip on the beat during lines. Clicks or crackles: raise buffer while mixing; disable heavy oversampling until render; close background apps. Preset sounds different at export: verify quality/oversampling modes; avoid master clipping; render at session rate. Chain feels “dead” on your mic: ease de-ess; reduce low-mid cuts; a tiny 150–180 Hz lift can restore chest without mud. Levels jump in A/B tests: match outputs with a final Gain; louder wins the ear unfairly. XVI. Learn more (next best step) Hand-offs are smoother when stems are clean and consistent. This walkthrough on how to export stems from Studio One step by step shows naming, starts, and tails that open cleanly anywhere. XVII. Quick action plan (copyable) Load an FX Chain or Track Preset; set input so raw peaks land −12 to −8 dBFS; Comp A kisses 3–5 dB. De-ess to “soft-bright,” add tiny Presence only if diction hides; keep Air conservative. Route Slap/Plate on FX channels; filter returns; duck Slap from the Lead; automate sends into hooks. Save role-based versions (Lead, Doubles, Harmonies, Ad-libs); keep a Song Template. Render roughs with headroom; keep the master unclipped; leave loudness for mastering. Used well, vocal presets are reliable shortcuts—not crutches. Keep headroom healthy, make small moves, automate what matters, and your voice will sit forward without harshness—song after song. For a fast start tuned to this DAW, grab the curated Studio One vocal presets and lock in your own “best-fit” versions for consistent, repeatable results.

더 알아보기
Use Vocal Presets in Pro Tools: Full Guide

Use Vocal Presets in Pro Tools: Full Guide

In Pro Tools, a vocal preset is a ready-to-load signal path—EQ, compression, de-essing, color, delay, and reverb—saved as a Track Preset, plug-in preset, or full session template. This guide walks you through pulling those presets into a session, calibrating input, shaping tone with a few decisive moves, routing effects the modern way, and keeping separate recipes for lead, doubles, harmonies, and ad-libs. If you’d like a jump start designed for this DAW, try the curated Pro Tools vocal presets and then tailor thresholds and sends to your voice. I. Presets in Pro Tools: what you can actually save Pro Tools gives you a few building blocks that cover most workflows: Track Presets — store inserts, their order, I/O, sends, and even color. Recall from the track nameplate or when creating a new track. Plug-in presets — AAX device states (EQs, compressors, de-essers, delays, reverbs) that you can mix and match inside any chain. Session Templates — open directly into a vocal-ready environment (lanes + FX returns) with one click. Import Session Data — cherry-pick a tuned vocal track (and its buses) from another session and drop it into your current one. Loading is step one. Step two—often skipped—is adapting gain, sibilance control, presence, and ambience to the singer and the song. II. Set the stage (short checklist) Before you hit record Playback Engine: choose your interface; 64–128 samples while tracking, then raise for mixing. Sample rate: 44.1 kHz for most releases (use 48 kHz when the project is headed to video). Healthy input: sing at performance level and target −12 to −8 dBFS on the raw input meter. Starter layout: one audio track named Lead Vox plus two aux returns: A = Slap, B = Plate. Meters: if you want to see gain before automation or sends, switch the track meter to pre-fader. III. Bringing a preset into the session (four dependable paths) 1) Track Presets (speed option) From the New Track dialog, choose Track Preset and select your vocal chain; or Right-click the track nameplate → Recall Track Preset…; or Open Workspace (Option+I) and drag a Track Preset onto the Edit/Mix window. Immediately store your version (e.g., Lead — Clean • YourName) so later tweaks do not overwrite the original. 2) Import Session Data (pull a lane with its plumbing) File → Import → Session Data… and choose a donor session with a vocal you trust. Enable the tuned Lead and its FX returns; if replacing a temp track, use “Match Tracks by Name.” 3) Session Template (open ready-to-record) Create from Template → pick your “Vocal Starter” (Lead, Doubles L/R, Harmonies, Ad-libs, Slap/Plate). Set the Lead input, arm, and you’re rolling—the buses are already patched. 4) Plug-in presets (surgical swaps) On the vocal track, load stock AAX tools (EQ3 7-Band, Dyn3 Comp/Lim, Dyn3 De-Esser, Mod Delay III, D-Verb/Space) or your third-party favorites. Save device presets that work; later, bundle them into a Track Preset for one-click recall. IV. Calibrate the signal (why your preset suddenly works) Preamp, then inserts: set the interface so unprocessed peaks land between −12 and −8 dBFS. Clip Gain first aid: tame shouty words and lift whispers before compression (±2–3 dB usually does it). Add short fades so edits are invisible. Compressor A sweet-spot: aim for roughly 3–5 dB gain reduction on phrases (2:1–3:1, 10–30 ms attack, 80–160 ms release). Heavy constant squeeze makes de-essing harder. After the chain: keep post-FX peaks around −6 to −3 dBFS. Loudness is a mastering decision, not a tracking one. Fair comparisons: add a Trim/Gain at the end of the chain so A/B tests aren’t won by “louder.” V. Five moves that shape 90% of a vocal Sibilance: set the de-esser band near 6–8 kHz; dial just enough that earbuds relax but consonants still read. Low-mid weight: add a touch at 120–200 Hz if the singer feels thin; if booth bloom shows up, shave 250–350 Hz instead. Presence lane: a wide, tiny lift around 3–4 kHz only when words hide. If cymbals are already bright, carve the beat rather than forcing the vocal. Air: small shelf at 10–12 kHz after sibilance is under control. Space: slapback around 90–120 ms and a short plate (0.7–1.0 s, 20–50 ms pre-delay). Keep verses drier; let choruses bloom. VI. One singer, many lanes: keep each job on its own rails Lead: mono-solid and stable in the center; width lives elsewhere. Ride phrases so the story never dips. Doubles L/R: higher high-pass than the Lead, slightly stronger de-ess, tucked 6–9 dB under; micro-pan left/right; avoid chorus wideners that collapse in mono. Harmonies: darker than doubles and spread wider; if they disappear, a tiny 5 kHz polish is enough. Ad-libs: narrowed bandwidth (HPF ~200 Hz, LPF 8–10 kHz), panned off-center, with short throws on transitions. Save a Track Preset per role (Lead — Clean, Double — Tight, Harmony — Wide, Ad-Lib — Phone) so recall is instant and consistent. VII. Ambience the modern way: two auxes, lots of control Create Aux A = Slap (Mod Delay III) and Aux B = Plate (D-Verb or Space). Filter both returns with EQ: HPF ~150 Hz, LPF ~6–7 kHz so tails never hiss on small speakers. Add a compressor on the Slap aux keyed from the Lead (fast attack/release, about 1–2 dB gain reduction). Echo appears in the gaps instead of stacking on words. Write simple send rides: +1–2 dB in hooks, pull back in dense verses. VIII. Stock toolkit that travels anywhere EQ3 7-Band (first): high-pass 80–100 Hz; gentle, wide cut at 250–350 Hz if boxy; tiny notch near 1 kHz only if needed. Dyn3 Comp/Lim (Comp A): 2:1–3:1, 10–30 ms attack, 80–160 ms release; kiss 3–5 dB on phrases. Dyn3 or Avid De-Esser: focus around 6–8 kHz; use ears, not meters. Dyn3 Comp/Lim (Comp B): faster “catcher” for 1–2 dB on peaks; stabilizes send level. Color (taste): AIR Lo-Fi or Distortion at very low mix for density; match output so “louder” doesn’t trick you. EQ3 (polish): broad +0.5–1 dB near 3–4 kHz if diction still hides; small air shelf last. Wrap the above as a Track Preset labeled clearly—Lead — Stock Clean (PT)—and spin lighter/heavier variants for different songs. IX. Evaluate presets quickly without fooling yourself Loop a 10–20 s section with soft words and loud ones. Keep a Trim/Gain at the end for level-match; flip Track Presets or plug-in stacks. Pick what translates on earbuds and a phone, not just the brightest option in the control room. X. If the beat is a single stereo file (tight hats, big subs) Let the vocal borrow space: on the instrumental bus, tie a gentle 2–4 kHz dip to a sidechained compressor keyed by the vocal—only 1–2 dB while the singer speaks. Top-end comfort: keep the Lead’s air move modest; low-pass the effects returns if cymbals already sizzle. Mono sanity check: collapse monitors briefly; the lyric should remain intelligible on a phone speaker. XI. Edit first, mix less: comping & Clip Gain Playlists: build a clean composite that favors diction and emotion. Pre-shape dynamics: quick Clip Gain nudges (±1–2 dB) smooth the ride so compressors do less heavy lifting. Breaths: reduce obvious gasps; keep the natural ones—they mark phrasing. XII. What to print (and when) Record dry while monitoring wet. Capture the clean Lead; if someone needs the “demo vibe,” route the Lead to a PRINT track and record a wet safety as well (Lead_Wet). Freeze or Commit heavy effects close to the finish line, and keep an _FXPRINT track for recall. XIII. Small automation, big payoff Level rides: +0.5–1 dB into downbeats; tiny dips on tongue-twisters. De-esser threshold: slightly tighter for bright syllables, looser for dark phrases. FX choreography: push Slap/Plate in the chorus; pull back for dense verses; keep returns filtered. XIV. Keep your library tidy (future-you will thank you) Names that sort: Lead — Clean, Lead — Air+, Rap — Punch, Harmony — Wide, Ad-Lib — Phone. One preset per lane: Lead/Doubles/Harmonies each get a dedicated Track Preset so you don’t over-de-ess stacks or brighten the center by accident. Session Template: keep a “Vocal Starter (PT)” with lanes and Slap/Plate auxes; start every song from it. XV. Troubleshooting: targeted fixes Air adds harshness: back off the shelf ~0.5 dB, lift the de-esser slightly, and low-pass the returns around 6–7 kHz. Vocal buried by 808: dry the sends in verses, add a hair of presence, and automate a subtle mid dip on the beat during lines. Clicks/crackles: increase buffer for mixing; disable look-ahead/heavy analyzers until bounce; close background apps. Preset sounds different on bounce: check quality/oversampling toggles, avoid master clipping, and bounce at the session rate. Chain feels flat on your mic: reduce low-mid cuts, ease the de-ess, and try a tiny 150–180 Hz lift for chest without mud. A/B bias: use the final Trim/Gain so loudness doesn’t decide the winner. XVI. One-page game plan Recall a Track Preset and calibrate input so raw peaks sit at −12 to −8 dBFS; Comp A glides at ~3–5 dB GR. Shape sibilance → body → presence → air with small, wide moves; keep FX tasteful in verses. Send to Slap/Plate auxes, filter returns, and sidechain-duck the Slap from the Lead. Store role-specific Track Presets (Lead, Doubles, Harmonies, Ad-libs) and use a session template. Print clean, keep headroom, and leave loudness for mastering. Used with intention, presets are a laser-cut shortcut—not a crutch. Keep headroom generous, make restrained moves, automate the few moments that matter, and the vocal will sit forward without grit or glare. When you want chains built for this exact ecosystem, start with the Pro Tools templates and lock in your own best-fit versions for repeatable results.

더 알아보기
How to Use Vocal Presets in Mixcraft

How to Use Vocal Presets in Mixcraft

In Mixcraft, a “vocal preset” is a reusable effects chain—EQ, compression, de-essing, tone color, delay, and reverb—that you can load on a track in one move. This guide shows how to pick and load the right preset, set healthy gain, shape tone, route sends, automate scenes, and save role-based versions for lead, doubles, harmonies, and ad-libs. Want a quick head start?  I. What a “vocal preset” is in Mixcraft Mixcraft supports several preset containers that make vocal chains easy to load and reuse: Effects Chain preset — a saved insert stack (order + settings) you can apply to any audio track. Track Template — an audio track saved with its chain, routing, color, and sends (e.g., Slap/Plate). Great when you want a full lane in one click. Project Template — a starter session with lanes (Lead, Doubles, Harmonies, Ad-libs) and Send tracks already set up. Using a preset is more than loading it—you’ll adapt input level, de-ess, presence, air, and FX balance to your voice and song. II. Pre-flight (so presets behave) Pre-flight checklist Audio device & buffer: select your interface; 64–128 samples to track, raise later for mixing. Session rate: 44.1 kHz for music (48 kHz if delivering to video). Input target: sing at performance volume; aim raw peaks around −12 to −8 dBFS before any FX. Track layout: start with one audio track named Lead Vox plus two Send tracks (A = Slap, B = Plate). Pop filter & distance: 10–20 cm from mic; keep stance consistent to stabilize tone. III. Load a vocal preset (four reliable routes) 1) Effects Chain preset (fastest) Select your Lead Vox track → open the FX window. Load an Effects Chain from the preset menu (or drag it from the Browser onto the FX area). Confirm the order: EQ → Comp A → De-Ess → (Color/Sat) → Comp B (catcher) → Utility. Immediately save your working copy with a clear name (e.g., Lead — Clean (YourName)). 2) Track Template (lane + sends in one move) Right-click in the track list → Insert Track From Template → choose your vocal template. Set the track input to your mic channel; arm and monitor. 3) Project Template (start ready every time) File → New Project → pick your “Vocal Starter” template (Lead/Doubles/Harmonies/Ad-libs + Slap/Plate sends). Set inputs and record; everything else is pre-wired. 4) Drag-drop from Browser Keep a _Presets/Vocals folder in the Browser; drag a chain onto the track when needed. IV. Gain staging: make or break Mic pre first: set the interface so unprocessed peaks hit −12 to −8 dBFS. Trim into Comp A: use the chain’s input/trim to hit ~3–5 dB gain reduction on phrases (ratio 2:1–3:1; attack 10–30 ms; release 80–160 ms). Don’t slam 10–12 dB constantly. After the rack: keep track peaks around −6 to −3 dBFS; loudness happens later in mastering. Level-match A/B: add a final trim/utility so preset comparisons aren’t biased by “louder wins.” V. Five controls you’ll touch on every song De-Ess (6–8 kHz): turn until earbuds stop complaining; stop before consonants blur. Body (120–200 Hz): add warmth if thin; if the booth sounds “boxy,” reduce 250–350 Hz instead. Presence (3–4 kHz): tiny, wide lift only if diction hides. If hats/claps are bright, carve the beat rather than boosting the voice. Air (10–12 kHz): micro shelf only after sibilance is calm. FX balance: slapback 90–120 ms and short plate 0.7–1.0 s (20–50 ms pre-delay). Verses drier; hooks open. VI. Lead vs. stacks: build a “family,” not clones Lead: mono-true center; minimal widening; automate volume to keep the story forward. Doubles L/R: higher HPF than Lead; a touch more de-ess; tuck −6 to −9 dB under; micro-pan left/right; avoid chorus wideners that collapse in mono. Harmonies: darker EQ; wider than doubles; optional +0.5–1 dB near 5 kHz for shimmer only if needed. Ad-libs: narrow bandwidth (HPF ~200 Hz, LPF ~8–10 kHz), side-panned, short throws on transitions. Save one preset per role—Lead — Clean, Double — Tight, Harmony — Wide, Ad-Lib — Phone—so recall is instant and consistent. VII. Time & space: Send tracks do the heavy lifting Create two Send tracks: A = Slap and B = Plate. Color them for quick spotting. On track A, add a short delay (≈90–110 ms), filter 150 Hz–6 kHz, low feedback. On track B, add a bright plate (0.7–1.0 s) with 20–50 ms pre-delay; HPF/LPF the return. Duck the Slap: place a compressor on A, sidechain from the Lead; fast attack/release so echoes bloom in the gaps. Automate sends: +1–2 dB into hooks; lower in dense verses; keep returns filtered for phone translation. VIII. Stock “safe chain” (rebuildable anywhere) EQ (first): HPF 80–100 Hz; wide −1 to −2 dB at 250–350 Hz if boxy; tight notch near 1 kHz if nasal. Compressor A (shape): ratio 2:1–3:1; attack 10–30 ms; release 80–160 ms; ~3–5 dB GR on phrases. De-Esser: center ~6–8 kHz; reduce until S/T/SH are comfortable on earbuds. Compressor B (catcher): faster 1–2 dB GR to stabilize sends and peaks. Color (optional): light saturation/tape; output matched so “louder” doesn’t fool you. EQ (polish): +0.5–1 dB broad at 3–4 kHz only if diction hides; tiny air shelf last. Delay & Reverb (sends): slap on A; plate on B; filter returns. Wrap it as an Effects Chain; save as Lead — Stock Clean (MX) and branch lighter/heavier versions per song. IX. Fast audition (without fooling your ears) Loop a 10–20 s phrase that includes quiet and loud words. Keep a final trim at the end of the chain; level-match before judging. Toggle chain presets; choose what translates on earbuds/phone, not just the brightest option. X. Two-track beat survival (bright hats, heavy subs) Carve, don’t fight: if the instrumental is a stereo file, cut small overlaps instead of “more bright” on vocals. A gentle dip around 2–4 kHz on the beat during vocal lines (via automation) lets consonants pop. Splash control: keep the Lead’s Air conservative; LPF returns ~6–7 kHz if hats are icy. Mono check: temporary mono on the master; the story should still land on a phone speaker. XI. Tracking vs. mixing: what to print Record dry, hear wet: monitor through the preset on the track but print a clean take. If a collaborator needs “demo vibe,” route Lead to a PRINT track and record a wet safety (Lead_Wet). Commit late: Freeze or render heavy FX near the end; keep an _FXPRINT audio track for recall. XII. Automation that sells the line (micro, not macro) Volume rides: +0.5–1 dB into downbeats; −0.5 dB on tongue-twisters. De-ess threshold: slightly tighter on bright syllables; looser on dark phrases. FX choreography: lift Slap/Plate into hooks; lower in verses; keep tails filtered. XIII. Organization & recall (minutes now, hours later) Names that sort: Lead — Clean, Lead — Air+, Rap — Punch, Harmony — Wide, Ad-Lib — Phone. One per role: separate chains for Lead/Doubles/Harmonies prevent over-de-essing stacks or over-brightening the center. Template: keep a “Starter — Vocals (Mixcraft)” project with lanes and two Send tracks. Duplicate for each new song. XIV. Troubleshooting (problem → focused move) Harsh S’s after adding Air: raise de-ess slightly; reduce Air by ~0.5 dB; LPF returns to ~6–7 kHz. Vocal sinks under 808: keep verses drier; add a tiny Presence lift; reduce delay feedback; consider a small 2–4 kHz dip on the beat during lines. Preset sounds different at export: check plug-in quality/latency modes; avoid master clipping; render at session rate. Clicks or crackles: raise buffer for mixing; disable heavy oversampling until render; close background apps. Chain feels “dead” on your mic: ease de-ess; reduce low-mid cuts; a tiny 150–180 Hz lift can restore chest without mud. Levels jump in A/B tests: match outputs with a final trim; louder wins the ear unfairly. XV. Quick action plan (copyable) Load an Effects Chain or Track Template; set input so raw peaks land −12 to −8 dBFS; Comp A kisses 3–5 dB. De-Ess to “soft-bright,” add tiny Presence only if diction hides; keep Air conservative. Route Slap/Plate on Send tracks; filter returns; duck Slap from the Lead; automate sends into hooks. Save role-based versions (Lead, Doubles, Harmonies, Ad-libs); keep a project template. Render roughs with headroom; keep the master unclipped; leave loudness for mastering. Used well, vocal presets are reliable shortcuts—not crutches. Keep headroom healthy, make small moves, automate what matters, and your voice will sit forward without harshness—song after song. When you want to start from chains already tuned for modern pop, rap, and R&B , explore vocal presets and lock in your own “best-fit” versions for fast, consistent sessions.

더 알아보기

믹싱 서비스

노래를 전문적으로 믹싱 및 마스터링해야 하는 경우, 저희 믹싱 및 마스터링 서비스를 자유롭게 확인해 보세요.

지금 탐색하기

보컬 프리셋

보컬 프리셋으로 보컬 트랙을 손쉽게 향상시키세요. 탁월한 성능을 위해 최적화된 이 프리셋은 다양한 음악 장르에서 뛰어난 보컬 품질을 달성하기 위한 완벽한 솔루션을 제공합니다. 몇 가지 간단한 조정만으로도 보컬이 선명하고 현대적인 우아함으로 돋보이게 되어, 보컬 프리셋은 모든 녹음 아티스트, 음악 프로듀서, 오디오 엔지니어에게 필수적인 자산으로 자리잡습니다.

지금 탐색하기

BCHILL MUSIC

안녕하세요! 제 이름은 Byron이고 저는 10년 이상의 경력을 가진 전문 음악 프로듀서이자 믹싱 엔지니어입니다. 오늘 믹싱/마스터링 서비스 문의하세요.

서비스

우리는 업계 표준 믹싱 서비스, 마스터링 서비스, 음악 제작 서비스뿐만 아니라 전문 녹음 및 믹싱 템플릿을 포함한 프리미엄 서비스를 고객에게 제공합니다.

혼합 서비스

지금 탐색하기

서비스 마스터링

서비스 마스터링

보컬 프리셋

지금 탐색하기
Adoric Bundles Embed