How to Mix Vocals Like Yeat (Rage & Trap Guide)

How to Mix Vocals Like Yeat (Rage & Trap Guide)

by Byron Hill II in News

Yeat’s vocal aesthetic is urgent, futuristic, and textured—tuned fast, framed by gritty saturation, and glued to wide, synth-heavy rage beats. This guide lays out the capture plan, routing, chain settings, FX playbook, stack strategy, and export targets so your mix hits on phones, earbuds, and big rooms. If you want a jump-start, audition proven vocal presets and adapt thresholds and sends to your voice.

I. The sonic fingerprint (what makes it “Yeat”)

Attitude first. Leads are pushed forward with fast tuning and present consonants. Ad-libs are bold—formant tricks, band-pass “phone” edges, or distorted shouts. The top is bright but controlled; the low-mids stay lean so the 808 breathes.

  • Tuning: decisive retune for rap-sing cadences; keep vowels natural with formant protection.
  • Texture: parallel or pre-EQ saturation for grit; de-ess before you add air.
  • Motion: triplet/dotted-eighth delays that pulse with the beat; compact verbs.
  • Width: chorus/micro-pitch on stacks; center lead stays stable.

II. Capture & session setup

Recording. 15–20 cm off a pop filter. Aim raw peaks around −12 to −8 dBFS. Avoid heavy EQ/comp on the way in; print clean so the mix chain can work. Keep takes tight; rage flows expose sloppy edits.

Session organization. Color code and route early. If a producer sends Ableton sessions or consolidated audio, confirm one start time for everything. When stems are needed from Ableton specifically, here’s a clear walkthrough to export stems from Ableton Live so files line up sample-accurately.

III. Routing architecture that fits rage beats

Set up buses so you can make confident, fast moves:

  • LEAD — main vocal lines.
  • DOUBLES — tight duplicates for body.
  • ADLIB FX — shout/texture lane (filters, formants, distortion).
  • VOCAL MASTER — all vocal buses feed here (light tone/control only).
  • MUSIC — the entire instrumental or a group of stems; carve here, not on the master.
  • 808 — separate bus for sub decisions; prevents broad EQ from dulling the kick.

Sends: mono slap, tempo delay, short plate/small hall, “throws” bus for word-end echoes. Keep returns filtered to avoid HF splash and low-end smear.

IV. Core chain (settings that translate)

Think “control + character.” Use small moves. Check on earbuds often.

  1. Pitch correction. Set key/scale. Fast retune for hooks; moderate for verses. Enable formant protection to keep tone from cartooning when melodies jump.
  2. Subtractive EQ. HPF 80–100 Hz (voice-dependent). If the booth adds “box,” dip 200–350 Hz (wide). If nasal, try a gentle notch near 1 kHz. Avoid narrow boosts—save boosts for later.
  3. Compressor 1 (shape). 2:1–3:1; attack 10–30 ms; release 80–200 ms or auto; 3–6 dB GR on phrases. Let consonants breathe so diction stays sharp.
  4. De-esser 1. Broad band around 6–8 kHz; reduce only what you hear on small speakers.
  5. Saturation for density. Tape/triode or transformer. Keep mix 5–15%. Match output so you aren’t fooled by “louder.”
  6. Compressor 2 (safety). Faster; 1–2 dB GR to tame spikes and make FX sends more even.
  7. Polish EQ. If the mic is dull: +0.5–1 dB at 3–4 kHz (presence). Air shelf +0.5–1 dB at 10–12 kHz if needed. If S’s rise, fix de-ess—not more air.
  8. Send FX. Mono slap (80–120 ms). Tempo delay (1/8, dotted-eighth, or triplet, low feedback). Small plate/room with 20–60 ms pre-delay. Use sidechain ducking on delays so repeats breathe between syllables.

V. FX playbook: formants, filters, and throws

Formant tricks. On ADLIB FX, use +2 to −3 semitone formant shifts for alien inflections. Keep the mix low; it should color, not hijack, the message.

Phone band-pass. 300 Hz–3 kHz band-pass plus slight distortion = gritty edges for transitions. Automate on single words before drops.

Triplet & dotted-eighth delay. Rage patterns love movement that syncs with hi-hat grids. Keep feedback modest; filter returns to ~6–7 kHz to avoid hiss.

Micro-pitch width (stacks only). ±5–9 cents on DOUBLES, short mod time. Keep the lead center dry so the image stays solid in mono.

Reverb discipline. Rage beats are busy; verbs should be compact. Short plate 0.6–1.0 s or a tight room. High-pass and low-pass every return.

VI. Make the voice sit inside the synth wall

Dynamic EQ on MUSIC bus. Sidechain a small 2–4 kHz dip from the lead. This opens consonants without making the vocal harsh.

808 coexistence. If syllables vanish under sub, apply a dynamic shelf at 120–180 Hz on the MUSIC or 808 bus keyed from the lead. Keep it subtle; the trick is clarity, not audible pumping.

Mid/side hygiene. Anchor low-mids in M. Let pads/synths widen in S. If the beat feels too bright, a tiny S-only dip at 9–10 kHz calms splash without dulling the lead.

Limiter temptation. For references, a clean limiter at −1.0 dBTP is fine. For your mix print, turn it off; let mastering set competitive loudness. If you’d rather hand off the final push, consider online mixing services to align balances, fix masking, and prep stems.

VII. Hooks, stacks, and ad-lib choreography

Doubles (body). Two tight doubles in the hook. High-pass a bit higher than the lead. More de-ess. Tuck each 6–9 dB below the lead. Pan lightly L/R if you want width without chorus swirl.

Octaves (impact). An octave-down layer under key words adds weight. Use heavier HPF, firm de-ess, and a darker tone so it supports rather than muddies.

Ad-libs (character). Shouts or formant-shifted phrases panned off-center; band-pass + drive for grit. Trigger triplet throws on bar turns. Keep them purposeful; fewer, better moments beat a crowded field.

Automation. Ride the lead ±1 dB into downbeats. Dip FX during dense consonants. Lift a throw by 0.5 dB only on the section entry—then return to normal.

VIII. Two complete chains (stock-only and third-party)

Stock-only chain (any DAW):

  1. Pitch: fast for hooks, moderate for verses; humanize/transition on; formants preserved.
  2. EQ: HPF 90 Hz; wide −2 dB at 250 Hz if muddy; micro notch near 1 kHz if nasal.
  3. Comp 1: 2:1; attack 20 ms; release 120 ms; 3–5 dB GR.
  4. De-esser: 6–8 kHz wide; 2–4 dB on S’s.
  5. Saturation: warm/tape, 5–10% mix.
  6. Comp 2: faster; 1–2 dB GR on peaks.
  7. EQ polish: +0.5–1 dB at 3.5 kHz if dull; tiny air shelf if needed.
  8. Sends: mono slap 90–110 ms; dotted-eighth delay; small plate with HPF/LPF.

Third-party flavor (example):

  1. Auto-Tune / Melodyne: quick for hooks; musical for verses; formants on.
  2. FabFilter Pro-Q 3: HPF 90 Hz; dynamic notch 250 Hz when the booth blooms.
  3. Opto comp (LA-2A-style): gentle body shaping.
  4. Resonance tamer (Sooth-style): light in 4–8 kHz only as needed.
  5. Analog/tube sat: low mix for density; match output.
  6. 1176-style comp: fast, 1–2 dB GR on peaks.
  7. Air EQ (Maag-style): micro +0.5–1 dB at 10–12 kHz if the mic is dark.
  8. FX: EchoBoy slap + triplet; short plate; filtered returns; occasional band-pass + drive on ADLIB FX.

IX. Troubleshooting (fast fixes that stick)

  • Air is sweet but S’s stab: broaden the de-ess band; reduce the air shelf by 0.5 dB; low-pass delay returns to ~6–7 kHz.
  • Lead sounds thin in hooks: ease the HPF a few Hz; +1 dB at 160–220 Hz (wide); blend 10–20% parallel warmth.
  • Words get swallowed by the 808: dynamic shelf at 120–180 Hz keyed from the lead on MUSIC/808; small 2–4 kHz duck on MUSIC when the vocal speaks.
  • Robotic tuning: slow retune slightly; raise humanize; keep formants on.
  • Stacks cloud the center: on DOUBLES bus, −1 to −2 dB at 250 Hz (wide), stronger de-ess, darker plate.

X. Export, loudness, and next steps

During mixing: keep raw vocal peaks around −12 to −8 dBFS. After processing, leave headroom; avoid a hard limiter on the mix bus so transients live.

Final bounce: stereo WAV, 24-bit at session rate. Target mix peaks near −3 dBFS with true peak ≤ −1.0 dBTP. Loudness belongs to mastering. 

XI. Wrap-up

“Yeat” vocals are a mix of precision and chaos: tuned and controlled, yet raw with texture and attitude. Keep low-mids tight, shape presence with restraint, let delays do the dancing, and reserve big distortion for ad-lib moments. Save a template for LEAD/DOUBLES/ADLIB FX/VOCAL MASTER, learn it deeply, and reference at one monitor level. If you want help locking balances to a brutal beat while you keep writing, lean on online mixing services; if you’re ready to ship, a focused pass of album and single mastering will finalize loudness, QC, and deliverables.

Previous Post Next Post

Related Posts

How to Use Vocal Presets in Studio One

How to Use Vocal Presets in Studio One

In Studio One, a “vocal preset” is a reusable channel chain—EQ, compression, de-essing, tone color, delay, and reverb—that you can load in one move. This guide shows how to choose and load presets (FX Chains and Track Presets), set healthy gain, adapt tone to your mic, route sends, automate scenes, and save role-based versions for lead, doubles, harmonies, and ad-libs. If you want a tuned springboard, browse purpose-built Studio One vocal presets and then fine-tune thresholds and sends for your voice and room. I. What a “vocal preset” is in Studio One Studio One gives you several preset containers that make vocal chains easy to load and reuse: FX Chain preset — a saved insert stack with Macro controls (one-click channel strip). Track Preset — recalls inserts, order, I/O, color, and sends for a track (Studio One 6+). Song Template — opens a whole session “studio-ready” (lanes + FX channels prewired). Device presets — per-plug-in settings (Pro EQ³/Pro EQ², Compressor, De-Esser, Analog Delay, Room Reverb/OpenAIR, etc.). Loading a preset is step one. Step two is adapting input level, de-ess amount, presence, air, and FX balance to your voice and the song. II. Pre-flight (so presets behave) Pre-flight checklist Audio device & buffer: smaller buffer (64–128) while tracking; raise later for mixing. Session rate: 44.1 kHz for music (48 kHz if delivering to video). Input target: sing at performance level; aim raw peaks around −12 to −8 dBFS before any inserts. Track layout: one audio track named Lead Vox and two FX channels (A = Slap, B = Plate). Pop filter & distance: 10–20 cm from mic; stay consistent to stabilize tone. III. Load a vocal preset (four reliable routes) 1) FX Chain preset (fastest, macro-ready) Open the Browser (F5) → Effects → FX Chains → drag your chain onto the Lead Vox channel. Click the Macro panel (wrench icon) to expose Trim, De-Ess, Body, Presence, Air, and FX controls. Save your working copy (right-click channel header → Store FX Chain) as Lead — Clean (YourName). 2) Track Preset (lane + sends in one move) Right-click a track header → Apply Track Preset… (or drag from Browser → Track Presets). Set input, arm, and monitor. Your inserts and sends load together. 3) Song Template (start ready) New Song → pick your “Vocal Starter” template with Lead/Doubles/Harmonies/Ad-libs and Slap/Plate FX channels. Set inputs and record; everything else is prewired. 4) Drag-drop device presets In the Browser, drag device presets (Pro EQ³, Compressor, De-Esser, etc.) into empty insert slots to build a chain, then Store FX Chain. IV. Gain staging: make or break Interface pre first: set the mic pre so unprocessed peaks land −12 to −8 dBFS. Clip Gain / Event Gain: nudge loud/soft phrases (±2–3 dB) before compression; add short fades at edit points. Comp A target: aim ~3–5 dB gain reduction on phrases (ratio 2:1–3:1; attack 10–30 ms; release 80–160 ms). Don’t slam 10–12 dB constantly. Post-chain peak: keep track peaks around −6 to −3 dBFS; leave loudness for mastering. Level-match A/B: keep a final Gain/Trim at chain end so comparing presets isn’t skewed by “louder wins.” V. Five controls you’ll touch on every song De-Ess (6–8 kHz): turn until earbuds stop complaining; stop before consonants blur. Body (120–200 Hz): add warmth if thin; if the booth is boxy, reduce 250–350 Hz instead. Presence (3–4 kHz): tiny, wide lift only if diction hides. If hats/claps are bright, carve the beat rather than boosting the voice. Air (10–12 kHz): micro shelf only after sibilance is calm. FX blend: slapback 90–120 ms + short plate 0.7–1.0 s (pre-delay 20–50 ms). Verses drier; hooks open. VI. Lead vs. stacks: build a “family,” not clones Lead: mono-true center; minimal wideners; ride volume to keep the story forward. Doubles L/R: higher HPF than Lead; a touch more de-ess; tuck −6 to −9 dB under; micro-pan L/R; avoid chorus wideners that collapse in mono. Harmonies: darker EQ; wider than doubles; optional +0.5–1 dB near 5 kHz for shimmer only if needed. Ad-libs: narrow bandwidth (HPF ~200 Hz, LPF ~8–10 kHz); side-panned; short throw echoes on transitions. Save one FX Chain or Track Preset per role—Lead — Clean, Double — Tight, Harmony — Wide, Ad-Lib — Phone—so recall is instant and consistent. VII. Time & space: FX channels do the heavy lifting Create two FX channels: A = Slap (Analog Delay or Beat Delay), B = Plate (Room Reverb/OpenAIR plate IR). Filter returns: insert Pro EQ³ on each FX channel; HPF ~150 Hz, LPF ~6–7 kHz so tails never hiss on earbuds. Ducking trick: insert Compressor on the Slap FX channel; sidechain from Lead; fast attack/release; ~1–2 dB GR so echoes bloom in the gaps. Send automation: +1–2 dB into hooks; lower in dense verses; keep tails filtered. VIII. Macro Controls (FX Chains = your channel strip) Open the FX Chain editor → Macro Controls. Create knobs: Trim, De-Ess, Body, Presence, Air, FX. Map each knob to the key parameter (e.g., De-Esser amount, Pro EQ shelves, Delay/Reverb sends). Set useful ranges so a quarter-turn does something musical, not extreme. Store the FX Chain so every session loads with your “channel strip” in one click. IX. Stock “safe chain” (rebuildable anywhere) Pro EQ³/Pro EQ² (first): HPF 80–100 Hz; wide −1 to −2 dB at 250–350 Hz if boxy; tight notch near 1 kHz if nasal. Compressor (Comp A, shape): ratio 2:1–3:1; attack 10–30 ms; release 80–160 ms; ~3–5 dB GR on phrases. De-Esser: center ~6–8 kHz; reduce until S/T/SH are comfortable on earbuds. Compressor (Comp B, catcher): faster, 1–2 dB GR to stabilize send levels and peaks. Color (optional): Softube-style Saturation Knob (if installed) or stock Saturation; very low mix; output matched. Pro EQ (polish): +0.5–1 dB broad at 3–4 kHz only if diction hides; tiny 10–12 kHz shelf last. Sends: Analog/Beat Delay for slap; Room Reverb/OpenAIR plate; filter returns. Wrap as an FX Chain; add Macro controls; save as Lead — Stock Clean (S1); branch lighter/heavier variants per song. X. Fast audition (without fooling your ears) Loop a 10–20 s phrase with quiet and loud words. Keep a final Gain at chain end to level-match; flip FX Chains or Track Presets from the Browser. Pick what translates on earbuds/phone, not just the brightest option. XI. Two-track beat survival (bright hats, heavy subs) When the instrumental is a stereo file, reduce collisions instead of “more bright” on the voice: Mid dip on the beat (dynamic): insert Pro EQ on the instrumental bus; create a gentle bell around 3 kHz; sidechain a Compressor to the vocal and link (or automate) the EQ band for −1–2 dB only while the voice speaks. Splash control: keep the Lead’s Air conservative; LPF returns ~6–7 kHz if hats are icy. Mono check: temporarily sum the monitor path; the story should still land on a phone speaker. XII. Tracking vs. mixing: what to print Record dry, hear wet: monitor through the preset on Lead but print a clean take. If a collaborator needs the “demo vibe,” bus Lead to a PRINT track and record a wet safety (Lead_Wet). Commit late: render/freeze heavy FX near the end; keep an _FXPRINT audio track for recall. XIII. Automation that sells the line (micro, not macro) Volume rides: +0.5–1 dB into downbeats; −0.5 dB on tongue-twisters. De-ess threshold: slightly tighter on bright syllables; looser on dark phrases. FX choreography: lift Slap/Plate into hooks; lower in verses; keep tails filtered. XIV. Organization & recall (minutes now, hours later) Names that sort: Lead — Clean, Lead — Air+, Rap — Punch, Harmony — Wide, Ad-Lib — Phone. One per role: separate FX Chains/Track Presets for Lead/Doubles/Harmonies prevent over-de-essing stacks or over-brightening the center. Template: keep a “Starter — Vocals (Studio One)” Song Template with lanes and FX channels; start every song from it. XV. Troubleshooting (problem → focused move) Harsh S’s after adding Air: raise De-Esser slightly; reduce Air ~0.5 dB; LPF returns to ~6–7 kHz. Vocal sinks under 808: keep verses drier; add a tiny Presence lift; apply a subtle 2–4 kHz dip on the beat during lines. Clicks or crackles: raise buffer while mixing; disable heavy oversampling until render; close background apps. Preset sounds different at export: verify quality/oversampling modes; avoid master clipping; render at session rate. Chain feels “dead” on your mic: ease de-ess; reduce low-mid cuts; a tiny 150–180 Hz lift can restore chest without mud. Levels jump in A/B tests: match outputs with a final Gain; louder wins the ear unfairly. XVI. Learn more (next best step) Hand-offs are smoother when stems are clean and consistent. This walkthrough on how to export stems from Studio One step by step shows naming, starts, and tails that open cleanly anywhere. XVII. Quick action plan (copyable) Load an FX Chain or Track Preset; set input so raw peaks land −12 to −8 dBFS; Comp A kisses 3–5 dB. De-ess to “soft-bright,” add tiny Presence only if diction hides; keep Air conservative. Route Slap/Plate on FX channels; filter returns; duck Slap from the Lead; automate sends into hooks. Save role-based versions (Lead, Doubles, Harmonies, Ad-libs); keep a Song Template. Render roughs with headroom; keep the master unclipped; leave loudness for mastering. Used well, vocal presets are reliable shortcuts—not crutches. Keep headroom healthy, make small moves, automate what matters, and your voice will sit forward without harshness—song after song. For a fast start tuned to this DAW, grab the curated Studio One vocal presets and lock in your own “best-fit” versions for consistent, repeatable results.

Learn more
Use Vocal Presets in Pro Tools: Full Guide

Use Vocal Presets in Pro Tools: Full Guide

In Pro Tools, a vocal preset is a ready-to-load signal path—EQ, compression, de-essing, color, delay, and reverb—saved as a Track Preset, plug-in preset, or full session template. This guide walks you through pulling those presets into a session, calibrating input, shaping tone with a few decisive moves, routing effects the modern way, and keeping separate recipes for lead, doubles, harmonies, and ad-libs. If you’d like a jump start designed for this DAW, try the curated Pro Tools vocal presets and then tailor thresholds and sends to your voice. I. Presets in Pro Tools: what you can actually save Pro Tools gives you a few building blocks that cover most workflows: Track Presets — store inserts, their order, I/O, sends, and even color. Recall from the track nameplate or when creating a new track. Plug-in presets — AAX device states (EQs, compressors, de-essers, delays, reverbs) that you can mix and match inside any chain. Session Templates — open directly into a vocal-ready environment (lanes + FX returns) with one click. Import Session Data — cherry-pick a tuned vocal track (and its buses) from another session and drop it into your current one. Loading is step one. Step two—often skipped—is adapting gain, sibilance control, presence, and ambience to the singer and the song. II. Set the stage (short checklist) Before you hit record Playback Engine: choose your interface; 64–128 samples while tracking, then raise for mixing. Sample rate: 44.1 kHz for most releases (use 48 kHz when the project is headed to video). Healthy input: sing at performance level and target −12 to −8 dBFS on the raw input meter. Starter layout: one audio track named Lead Vox plus two aux returns: A = Slap, B = Plate. Meters: if you want to see gain before automation or sends, switch the track meter to pre-fader. III. Bringing a preset into the session (four dependable paths) 1) Track Presets (speed option) From the New Track dialog, choose Track Preset and select your vocal chain; or Right-click the track nameplate → Recall Track Preset…; or Open Workspace (Option+I) and drag a Track Preset onto the Edit/Mix window. Immediately store your version (e.g., Lead — Clean • YourName) so later tweaks do not overwrite the original. 2) Import Session Data (pull a lane with its plumbing) File → Import → Session Data… and choose a donor session with a vocal you trust. Enable the tuned Lead and its FX returns; if replacing a temp track, use “Match Tracks by Name.” 3) Session Template (open ready-to-record) Create from Template → pick your “Vocal Starter” (Lead, Doubles L/R, Harmonies, Ad-libs, Slap/Plate). Set the Lead input, arm, and you’re rolling—the buses are already patched. 4) Plug-in presets (surgical swaps) On the vocal track, load stock AAX tools (EQ3 7-Band, Dyn3 Comp/Lim, Dyn3 De-Esser, Mod Delay III, D-Verb/Space) or your third-party favorites. Save device presets that work; later, bundle them into a Track Preset for one-click recall. IV. Calibrate the signal (why your preset suddenly works) Preamp, then inserts: set the interface so unprocessed peaks land between −12 and −8 dBFS. Clip Gain first aid: tame shouty words and lift whispers before compression (±2–3 dB usually does it). Add short fades so edits are invisible. Compressor A sweet-spot: aim for roughly 3–5 dB gain reduction on phrases (2:1–3:1, 10–30 ms attack, 80–160 ms release). Heavy constant squeeze makes de-essing harder. After the chain: keep post-FX peaks around −6 to −3 dBFS. Loudness is a mastering decision, not a tracking one. Fair comparisons: add a Trim/Gain at the end of the chain so A/B tests aren’t won by “louder.” V. Five moves that shape 90% of a vocal Sibilance: set the de-esser band near 6–8 kHz; dial just enough that earbuds relax but consonants still read. Low-mid weight: add a touch at 120–200 Hz if the singer feels thin; if booth bloom shows up, shave 250–350 Hz instead. Presence lane: a wide, tiny lift around 3–4 kHz only when words hide. If cymbals are already bright, carve the beat rather than forcing the vocal. Air: small shelf at 10–12 kHz after sibilance is under control. Space: slapback around 90–120 ms and a short plate (0.7–1.0 s, 20–50 ms pre-delay). Keep verses drier; let choruses bloom. VI. One singer, many lanes: keep each job on its own rails Lead: mono-solid and stable in the center; width lives elsewhere. Ride phrases so the story never dips. Doubles L/R: higher high-pass than the Lead, slightly stronger de-ess, tucked 6–9 dB under; micro-pan left/right; avoid chorus wideners that collapse in mono. Harmonies: darker than doubles and spread wider; if they disappear, a tiny 5 kHz polish is enough. Ad-libs: narrowed bandwidth (HPF ~200 Hz, LPF 8–10 kHz), panned off-center, with short throws on transitions. Save a Track Preset per role (Lead — Clean, Double — Tight, Harmony — Wide, Ad-Lib — Phone) so recall is instant and consistent. VII. Ambience the modern way: two auxes, lots of control Create Aux A = Slap (Mod Delay III) and Aux B = Plate (D-Verb or Space). Filter both returns with EQ: HPF ~150 Hz, LPF ~6–7 kHz so tails never hiss on small speakers. Add a compressor on the Slap aux keyed from the Lead (fast attack/release, about 1–2 dB gain reduction). Echo appears in the gaps instead of stacking on words. Write simple send rides: +1–2 dB in hooks, pull back in dense verses. VIII. Stock toolkit that travels anywhere EQ3 7-Band (first): high-pass 80–100 Hz; gentle, wide cut at 250–350 Hz if boxy; tiny notch near 1 kHz only if needed. Dyn3 Comp/Lim (Comp A): 2:1–3:1, 10–30 ms attack, 80–160 ms release; kiss 3–5 dB on phrases. Dyn3 or Avid De-Esser: focus around 6–8 kHz; use ears, not meters. Dyn3 Comp/Lim (Comp B): faster “catcher” for 1–2 dB on peaks; stabilizes send level. Color (taste): AIR Lo-Fi or Distortion at very low mix for density; match output so “louder” doesn’t trick you. EQ3 (polish): broad +0.5–1 dB near 3–4 kHz if diction still hides; small air shelf last. Wrap the above as a Track Preset labeled clearly—Lead — Stock Clean (PT)—and spin lighter/heavier variants for different songs. IX. Evaluate presets quickly without fooling yourself Loop a 10–20 s section with soft words and loud ones. Keep a Trim/Gain at the end for level-match; flip Track Presets or plug-in stacks. Pick what translates on earbuds and a phone, not just the brightest option in the control room. X. If the beat is a single stereo file (tight hats, big subs) Let the vocal borrow space: on the instrumental bus, tie a gentle 2–4 kHz dip to a sidechained compressor keyed by the vocal—only 1–2 dB while the singer speaks. Top-end comfort: keep the Lead’s air move modest; low-pass the effects returns if cymbals already sizzle. Mono sanity check: collapse monitors briefly; the lyric should remain intelligible on a phone speaker. XI. Edit first, mix less: comping & Clip Gain Playlists: build a clean composite that favors diction and emotion. Pre-shape dynamics: quick Clip Gain nudges (±1–2 dB) smooth the ride so compressors do less heavy lifting. Breaths: reduce obvious gasps; keep the natural ones—they mark phrasing. XII. What to print (and when) Record dry while monitoring wet. Capture the clean Lead; if someone needs the “demo vibe,” route the Lead to a PRINT track and record a wet safety as well (Lead_Wet). Freeze or Commit heavy effects close to the finish line, and keep an _FXPRINT track for recall. XIII. Small automation, big payoff Level rides: +0.5–1 dB into downbeats; tiny dips on tongue-twisters. De-esser threshold: slightly tighter for bright syllables, looser for dark phrases. FX choreography: push Slap/Plate in the chorus; pull back for dense verses; keep returns filtered. XIV. Keep your library tidy (future-you will thank you) Names that sort: Lead — Clean, Lead — Air+, Rap — Punch, Harmony — Wide, Ad-Lib — Phone. One preset per lane: Lead/Doubles/Harmonies each get a dedicated Track Preset so you don’t over-de-ess stacks or brighten the center by accident. Session Template: keep a “Vocal Starter (PT)” with lanes and Slap/Plate auxes; start every song from it. XV. Troubleshooting: targeted fixes Air adds harshness: back off the shelf ~0.5 dB, lift the de-esser slightly, and low-pass the returns around 6–7 kHz. Vocal buried by 808: dry the sends in verses, add a hair of presence, and automate a subtle mid dip on the beat during lines. Clicks/crackles: increase buffer for mixing; disable look-ahead/heavy analyzers until bounce; close background apps. Preset sounds different on bounce: check quality/oversampling toggles, avoid master clipping, and bounce at the session rate. Chain feels flat on your mic: reduce low-mid cuts, ease the de-ess, and try a tiny 150–180 Hz lift for chest without mud. A/B bias: use the final Trim/Gain so loudness doesn’t decide the winner. XVI. One-page game plan Recall a Track Preset and calibrate input so raw peaks sit at −12 to −8 dBFS; Comp A glides at ~3–5 dB GR. Shape sibilance → body → presence → air with small, wide moves; keep FX tasteful in verses. Send to Slap/Plate auxes, filter returns, and sidechain-duck the Slap from the Lead. Store role-specific Track Presets (Lead, Doubles, Harmonies, Ad-libs) and use a session template. Print clean, keep headroom, and leave loudness for mastering. Used with intention, presets are a laser-cut shortcut—not a crutch. Keep headroom generous, make restrained moves, automate the few moments that matter, and the vocal will sit forward without grit or glare. When you want chains built for this exact ecosystem, start with the Pro Tools templates and lock in your own best-fit versions for repeatable results.

Learn more
How to Use Vocal Presets in Mixcraft

How to Use Vocal Presets in Mixcraft

In Mixcraft, a “vocal preset” is a reusable effects chain—EQ, compression, de-essing, tone color, delay, and reverb—that you can load on a track in one move. This guide shows how to pick and load the right preset, set healthy gain, shape tone, route sends, automate scenes, and save role-based versions for lead, doubles, harmonies, and ad-libs. Want a quick head start?  I. What a “vocal preset” is in Mixcraft Mixcraft supports several preset containers that make vocal chains easy to load and reuse: Effects Chain preset — a saved insert stack (order + settings) you can apply to any audio track. Track Template — an audio track saved with its chain, routing, color, and sends (e.g., Slap/Plate). Great when you want a full lane in one click. Project Template — a starter session with lanes (Lead, Doubles, Harmonies, Ad-libs) and Send tracks already set up. Using a preset is more than loading it—you’ll adapt input level, de-ess, presence, air, and FX balance to your voice and song. II. Pre-flight (so presets behave) Pre-flight checklist Audio device & buffer: select your interface; 64–128 samples to track, raise later for mixing. Session rate: 44.1 kHz for music (48 kHz if delivering to video). Input target: sing at performance volume; aim raw peaks around −12 to −8 dBFS before any FX. Track layout: start with one audio track named Lead Vox plus two Send tracks (A = Slap, B = Plate). Pop filter & distance: 10–20 cm from mic; keep stance consistent to stabilize tone. III. Load a vocal preset (four reliable routes) 1) Effects Chain preset (fastest) Select your Lead Vox track → open the FX window. Load an Effects Chain from the preset menu (or drag it from the Browser onto the FX area). Confirm the order: EQ → Comp A → De-Ess → (Color/Sat) → Comp B (catcher) → Utility. Immediately save your working copy with a clear name (e.g., Lead — Clean (YourName)). 2) Track Template (lane + sends in one move) Right-click in the track list → Insert Track From Template → choose your vocal template. Set the track input to your mic channel; arm and monitor. 3) Project Template (start ready every time) File → New Project → pick your “Vocal Starter” template (Lead/Doubles/Harmonies/Ad-libs + Slap/Plate sends). Set inputs and record; everything else is pre-wired. 4) Drag-drop from Browser Keep a _Presets/Vocals folder in the Browser; drag a chain onto the track when needed. IV. Gain staging: make or break Mic pre first: set the interface so unprocessed peaks hit −12 to −8 dBFS. Trim into Comp A: use the chain’s input/trim to hit ~3–5 dB gain reduction on phrases (ratio 2:1–3:1; attack 10–30 ms; release 80–160 ms). Don’t slam 10–12 dB constantly. After the rack: keep track peaks around −6 to −3 dBFS; loudness happens later in mastering. Level-match A/B: add a final trim/utility so preset comparisons aren’t biased by “louder wins.” V. Five controls you’ll touch on every song De-Ess (6–8 kHz): turn until earbuds stop complaining; stop before consonants blur. Body (120–200 Hz): add warmth if thin; if the booth sounds “boxy,” reduce 250–350 Hz instead. Presence (3–4 kHz): tiny, wide lift only if diction hides. If hats/claps are bright, carve the beat rather than boosting the voice. Air (10–12 kHz): micro shelf only after sibilance is calm. FX balance: slapback 90–120 ms and short plate 0.7–1.0 s (20–50 ms pre-delay). Verses drier; hooks open. VI. Lead vs. stacks: build a “family,” not clones Lead: mono-true center; minimal widening; automate volume to keep the story forward. Doubles L/R: higher HPF than Lead; a touch more de-ess; tuck −6 to −9 dB under; micro-pan left/right; avoid chorus wideners that collapse in mono. Harmonies: darker EQ; wider than doubles; optional +0.5–1 dB near 5 kHz for shimmer only if needed. Ad-libs: narrow bandwidth (HPF ~200 Hz, LPF ~8–10 kHz), side-panned, short throws on transitions. Save one preset per role—Lead — Clean, Double — Tight, Harmony — Wide, Ad-Lib — Phone—so recall is instant and consistent. VII. Time & space: Send tracks do the heavy lifting Create two Send tracks: A = Slap and B = Plate. Color them for quick spotting. On track A, add a short delay (≈90–110 ms), filter 150 Hz–6 kHz, low feedback. On track B, add a bright plate (0.7–1.0 s) with 20–50 ms pre-delay; HPF/LPF the return. Duck the Slap: place a compressor on A, sidechain from the Lead; fast attack/release so echoes bloom in the gaps. Automate sends: +1–2 dB into hooks; lower in dense verses; keep returns filtered for phone translation. VIII. Stock “safe chain” (rebuildable anywhere) EQ (first): HPF 80–100 Hz; wide −1 to −2 dB at 250–350 Hz if boxy; tight notch near 1 kHz if nasal. Compressor A (shape): ratio 2:1–3:1; attack 10–30 ms; release 80–160 ms; ~3–5 dB GR on phrases. De-Esser: center ~6–8 kHz; reduce until S/T/SH are comfortable on earbuds. Compressor B (catcher): faster 1–2 dB GR to stabilize sends and peaks. Color (optional): light saturation/tape; output matched so “louder” doesn’t fool you. EQ (polish): +0.5–1 dB broad at 3–4 kHz only if diction hides; tiny air shelf last. Delay & Reverb (sends): slap on A; plate on B; filter returns. Wrap it as an Effects Chain; save as Lead — Stock Clean (MX) and branch lighter/heavier versions per song. IX. Fast audition (without fooling your ears) Loop a 10–20 s phrase that includes quiet and loud words. Keep a final trim at the end of the chain; level-match before judging. Toggle chain presets; choose what translates on earbuds/phone, not just the brightest option. X. Two-track beat survival (bright hats, heavy subs) Carve, don’t fight: if the instrumental is a stereo file, cut small overlaps instead of “more bright” on vocals. A gentle dip around 2–4 kHz on the beat during vocal lines (via automation) lets consonants pop. Splash control: keep the Lead’s Air conservative; LPF returns ~6–7 kHz if hats are icy. Mono check: temporary mono on the master; the story should still land on a phone speaker. XI. Tracking vs. mixing: what to print Record dry, hear wet: monitor through the preset on the track but print a clean take. If a collaborator needs “demo vibe,” route Lead to a PRINT track and record a wet safety (Lead_Wet). Commit late: Freeze or render heavy FX near the end; keep an _FXPRINT audio track for recall. XII. Automation that sells the line (micro, not macro) Volume rides: +0.5–1 dB into downbeats; −0.5 dB on tongue-twisters. De-ess threshold: slightly tighter on bright syllables; looser on dark phrases. FX choreography: lift Slap/Plate into hooks; lower in verses; keep tails filtered. XIII. Organization & recall (minutes now, hours later) Names that sort: Lead — Clean, Lead — Air+, Rap — Punch, Harmony — Wide, Ad-Lib — Phone. One per role: separate chains for Lead/Doubles/Harmonies prevent over-de-essing stacks or over-brightening the center. Template: keep a “Starter — Vocals (Mixcraft)” project with lanes and two Send tracks. Duplicate for each new song. XIV. Troubleshooting (problem → focused move) Harsh S’s after adding Air: raise de-ess slightly; reduce Air by ~0.5 dB; LPF returns to ~6–7 kHz. Vocal sinks under 808: keep verses drier; add a tiny Presence lift; reduce delay feedback; consider a small 2–4 kHz dip on the beat during lines. Preset sounds different at export: check plug-in quality/latency modes; avoid master clipping; render at session rate. Clicks or crackles: raise buffer for mixing; disable heavy oversampling until render; close background apps. Chain feels “dead” on your mic: ease de-ess; reduce low-mid cuts; a tiny 150–180 Hz lift can restore chest without mud. Levels jump in A/B tests: match outputs with a final trim; louder wins the ear unfairly. XV. Quick action plan (copyable) Load an Effects Chain or Track Template; set input so raw peaks land −12 to −8 dBFS; Comp A kisses 3–5 dB. De-Ess to “soft-bright,” add tiny Presence only if diction hides; keep Air conservative. Route Slap/Plate on Send tracks; filter returns; duck Slap from the Lead; automate sends into hooks. Save role-based versions (Lead, Doubles, Harmonies, Ad-libs); keep a project template. Render roughs with headroom; keep the master unclipped; leave loudness for mastering. Used well, vocal presets are reliable shortcuts—not crutches. Keep headroom healthy, make small moves, automate what matters, and your voice will sit forward without harshness—song after song. When you want to start from chains already tuned for modern pop, rap, and R&B , explore vocal presets and lock in your own “best-fit” versions for fast, consistent sessions.

Learn more

Mixing Services

Feel free to check out ou mixing and mastering services if you are in need of having your song professionally mixed and mastered.

Explore Now

Vocal Presets

Elevate your vocal tracks effortlessly with Vocal Presets. Optimized for exceptional performance, these presets offer a complete solution for achieving outstanding vocal quality in various musical genres. With just a few simple tweaks, your vocals will stand out with clarity and modern elegance, establishing Vocal Presets as an essential asset for any recording artist, music producer, or audio engineer.

Explore Now

BCHILL MUSIC

Hey! My name is Byron and I am a professional music producer & mixing engineer of 10+ years. Contact me for your mixing/mastering services today.

SERVICES

We provide premium services for our clients including industry standard mixing services, mastering services, music production services as well as professional recording and mixing templates.

Mixing Services

Explore Now

Mastering Services

Mastering Services

Vocal Presets

Explore Now
Adoric Bundles Embed